POLAGARD FIBRELASTIC is a single component, premium quality elastomeric wall coating designed for permanent flexibility and toughness. It will accept movement from thermal changes and bridge hairline cracks. POLAGARD FIBRELASTIC provides a waterproof finish that is both decorative and long-lasting, and it may be applied directly to most surfaces including concrete, splitface block, brick, stucco, wood, asbestos shingles, concrete block, mineral composites and precast concrete.
OUTSTANDING FEATURES:
§
Contains micro-fibers that bridge hairline cracks
§ Remains flexible, elastomeric and waterproof
§ Resists UV, mildew and chemical attack; has excellent alkali resistance
§
Has very good resistance to staining and salt penetration
§ Resists dirt pickup and chalking
§ Provides long-lasting weather-tight protection
§ Easy and safe to apply, with easy cleanup and low odor
§ Produces a breathable coating; protects from rain, wind, snow and ice
§
Will not support
combustion in the event of fire
§
Can be applied by brush, roller or airless spray
SPECIFICATIONS:
Coating Type: | Elastomeric PVC/acrylic waterborne coating |
VOC: | Zero grams/liter |
Pot Life: | Single component |
Shelf Life: | 12 months |
Recommended Thickness: | 120 square feet per gallon average per coat |
Coverage: | 30 to 40 square feet/gallon |
Packaging: | 5 U.S. gallons; 1 gallon & 55 gallon sizes available |
Color: | 26 standard colors available |
APPLICATION:
Caution! READ THIS ENTIRE PRODUCT DATA SHEET BEFORE APPLICATION.
Surface must be firm and free of dirt, efflorescence, oils, grease, loose debris or any other substance that may interfere with bond. It is advisable to have a dry substrate. If the surface is damp, test the surface first by applying coating to a 4' x 4' area. If no sags or runs occur within 30 minutes and the coating appears to be taking a normal cure, application can proceed. Previously coated or treated surfaces must be tested prior to application to insure proper adhesion. It is advisable to fill any heavily pocked, spalled or broken areas of substrate. Repair cracks greater than 1/16" with a premium grade of acrylic caulk. Mound the caulk slightly so that the repair is flush with the wall surface and allow to cure 4-6 hours. Apply POLAGARD FIBRELASTIC over repaired areas. POLAGARD FIBRELASTIC may be brushed, airless sprayed, or rolled. For airless spray, be sure to use a reversible tip (a #35 orifice is a recommended starting tip). For roller application, a l¼” nap roller provides good results. The nap thickness can be varied to accommodate the substrate. POLAGARD FIBRELASTIC may be thinned with no more than 3-5 oz. of water per gallon. For waterproofing, apply 2 coats at 15-20 mils thickness per coat. When spray applied, it is advisable to backroll the first coat to insure optimum weatherproofing and reduce pinholing. Power stir product for 2 minutes at low speed before use. Always apply to the shaded areas of the building with ambient surface temperatures. Unshaded areas may have high surface temperatures that can cause rapid skinning of the coating and blisters may appear.
LIMITATIONS:
Do not apply to frozen or saturated surfaces. Do not apply if temperature falls below 45°F within 4 hours unless an artificial heat source and enclosure are provided. High humidity and precipitation interfere with application and adhesion. Do not apply if rain is forecast within 8 hours of application completion. Shelf life in unopened containers is 1 year at 45°-90°F. Protect POLAGARD FIBRELASTIC from freezing. Keep containers sealed and under cover when not in use.
MAINTENANCE:
If a treated surface becomes dirty, spray with water or a mild soapy water solution. Rinse with a clean, low pressure water spray. For scars or hard-to-clean areas, recoat with POLAGARD FIBRELASTIC.
PRECAUTIONS:
POLAGARD FIBRELASTIC is an alkaline, water based product. Avoid contact with skin and eyes. In case of contact, immediately flush with clear water. For contact with eyes, get medical attention in addition to flushing. Avoid inhalation of spray mist. If spray mist is inhaled, seek medical attention immediately. In case of ingestion, contact a physician immediately. Wear rubber gloves, coveralls, and safety goggles when applying POLAGARD FIBRELASTIC. Keep product out of reach of children and pets. For additional information, contact our Technical Department.
TECHNICAL DATA:
Moisture Vapor Transmission: | 2.5 perms | ASTM E-96 |
Elongation: | 180% (60°F) | ASTM D-412 |
Solids Content: | 67% (B.W.); 64% (B.V.) | ASTM D-1044 |
Tensile Strength: | 350 psi | ASTM D-412 |
FSI Rating: | Class 'A' | ASTM E-84 |
Flashpoint: | Non-flammable | SETA |
Viscosity: | 20,000 cps | |
Weight Per Gallon: | 11 pounds | |
pH: | 9.0 - 9.5 | |
Fiber Type: | Calcium Silicate | |
Fiber Aspect Ratio: | 80:1 | |
Pigment Type: | Non-chalking | UV rated |
Colorant Type: | Exterior Grade | UV rated |
Alkalinity Resistance: | Excellent | |
NOTICE: The information presented herein is based on tests and data that Andek Corporation believes to be reliable. It is intended for use by technically qualified personnel at their own discretion and risk. Since conditions of handling and use are beyond our control, we make no warranties, express or implied, and assume no liability in connection with any use of this information. Nothing herein is to be construed as a license to operate or a recommendation to infringe any patent.
